sbm/sbm what effect magnetic sinter in blast furnace.md …
sbm / sbm what effect magnetic sinter in blast furnace.md. maekesi a6025507b6 s. 2022-11-01 16:58:18 +08:00
sbm / sbm what effect magnetic sinter in blast furnace.md. maekesi a6025507b6 s. 2022-11-01 16:58:18 +08:00
into the blast furnace in mixture with sinter. This idea was successfully tested.1) Presently the majority of blast furnaces in Europe, Japan and elsewhere use nut coke although its amount is very different: from 10–20 to 70–100kg/tHM and more.2) Oper-ation of many blast furnaces has proved the possibility of
The effects of Al2O3, MgO, and binary basicity on the viscosity of high alumina blast furnace slag are studied systematically at the temperatures of 1773 K and below using the orthogonal ...
High RDI sinter deteriorates gas permeability in the upper part of the blast furnace because the particle size of the sinter is easily reduced by reduction degradation (powdering) in …
Manganese Ferroalloys Technology - ScienceDirect. Jan 01, 2013· Blast furnace smelting has serious disadvantages, such as high coke consumption (~1500 to 2000 kg/t of alloy, which is five to six times higher than in electric furnaces) and high losses of manganese in slag and off-gases.
Conventionally as means for improving permeability in the blast furnace, improvement of high temperature properties of raw materials at the high temperature, [1][2][3][4] charging distribution ...
used as a raw material for blast furnaces, but it can be used as raw material for pellets or sintered iron ore, hereinafter re-ferred to as sinter. Sinter accounts for approximately 73% of iron ore charged in blast furnaces in Japan [6], and it is cru-cial to improve the reduction efficiency of sinter in blast fur-nace operation.
Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter …
Today's main share of the worldwide high-carbon ferromanganese (HCFeMn) production is realized in submerged arc furnaces (SAF) by carbo-thermic …
Herein, the reducibility of the iron ore pellet, sinter, and lump ore in the BF shaft are focused on. The experiments are conducted isothermally with a blast furnace simulator (BFS) high-temperature furnace at four different temperatures (700, 800, 900, and 1000 °C) for 300 min.
An increase in the content of manganese oxide in the sinter improves the filterability of the primary slag, but it has this effect only if manganese is introduced into …
In this work, the effect of high Blaine fineness (2700–3250 cm²/g) on the pellets properties has been studied and the optimum parameters to make it usable for blast furnace have been examined ...
A method for estimating the input of nut coke to the blast-furnace hearth is proposed. It takes into account the specific surface area of the loaded fuels, the reduction of oxides into elements of iron, and the carburization of iron. It is shown that if nut coke in an amount of up to 100 kg/ton of iron is loaded into the iron-ore part of the charge, its input …
The quality of iron ore sinter mainly depends on sinter mineralogy, which in turn depends on the chemical composition of the sinter mix. The reduction properties of the mineral phases formed in the sinter influences the sinter reducibility. MgO has a varying effect on sinter reducibility at different silica contents.
Reduction Disintegration Index ( RDI) is one key factor of sinter quality, which indicates the degree of disintegration by the reducing gas at about 550 in the middle of the blast furnace shaft. This is related to the permeability and reduction reaction between gas and sinter in the blast furnace, so appropriate quality control is essential. RDI is influenced by …
The article describes the concept of partially replacing the sinter in a blast furnace charge with extrusion briquettes to form the basis for sintering and briquetting synergy. The comparability criteria for sinter and extrusion briquette (brex) properties and production parameters were analyzed along with a substantiation of the fundamental …
So, the sintering process main objectives are to increase the size of ore additives to a level acceptable to the blast furnace for improving permeability of burden inside the BF; to form a strong agglomerate with high bulk reducibility; to remove volatile matter like CO 2 from carbonates, H 2 O from hydroxides, and sulfur from sulfide type of …
Abstract: ed glass-ceramics were prepared via a single-step sintering method using high-titanium blast furnace slag and waste glass as the main raw materials The influence of sintering temperature (900–1060°C) on the microstructure and properties of ed glass-ceramics was studied.
Iron oxides are reduced in the blast furnace (Fig. 4.1), and the resulting material is melted.Blast furnaces capacity is 100–5000 m 3 covering the 70% of the global steel production. Iron ores, sinter or pellets, coke, and lime are introduced into the blast furnace from the top; the hot compressed air is fluxed from tuyeres at the lower section …
This chapter first gives an overview of the blast furnace ironmaking fundamentals including zones within the furnace and redox reactions involved, and then …
Results are provided for calculation of the predicted blast furnace operating regime using converter slag in the iron-ore part of the charge without implementing additional measures with the aim of evaluating its effect on process indices. Introduction into a blast furnace charge of fractionated converter slag may be performed in order to increase slag …
As a promising method to strengthen the blast furnace smelting and to realize reduced fuel operation, high-proportion pellet charging has become the practice of BF ironmaking. Use of pellet gives rise to uniform bed permeability in comparison with iron ore or sinter. This leads to better gas–solid contact resulting in higher productivity at …
Behaviour of chlorine and alkalis in the blast furnace and effect on sinter properties during reduction - Volume 101 Issue 1. Last updated 27/06/24: Online ordering is currently unavailable due to technical issues. We apologise for any delays responding to customers while we resolve this. ... High Temperature Materials and Processes, Vol. 38 ...
The experimentation allowing comparison of manganese ore fines pellet sintering and traditional sintering of manganese ore fines in terms of sintering performance are studied. The results show that, compared with traditional sintering, the pellet-sintering process can significantly reduce the coke level while ensuring the …
The basicity required for iron ore sinter is set by blast furnace slag composition requirements, and therefore varies with the proportion lump iron ore in the burden.
The results show that the reduction degradation process of sinter in blast furnace can be divided into three stages, the most dramatic degradation behavior occurs between 400℃ and 600℃ as the ...
The article describes the concept of partially replacing the sinter in a blast furnace charge with extrusion briquettes to form the basis for sintering and briquetting …
Hot metal production using sinter and pellets in the blast furnace is compared, considering aspects like; blast furnace productivity, environmental performance, solid waste management, slag-coke ...
The depletion of sulfide nickel ore and the growing of stainless steel demand each year cause the use of low-grade laterite nickel ore continues to increase. Due to very low nickel content, there is no optimal process to extract them. One of the alternative processes being developed now is the sintering-blast furnace process which produces …
improvement of gas permeability in the blast furnace. 2. Experimental Method 2.1. Sinter Properties and Reducing Gas Conditions Used in Experiments In order to evaluate the effect of sinter properties on gas permeability in the blast furnace, four types of sinter (A)– (D) with different RI, RDI, and chemical compositions were used.